#151 [↑][↓]  22-06-2022 22:47:17

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Version 1.6.1 disponible...
Mise à jour "conséquente"...

https://forums.x-pilot.com/forums/topic … -released/





Release Highlights:

2988: Elevator control system is missing gain change mechanism from control column, causing over-controlling at higher speeds
3121: Implement variable pitch feel based on stabilizer trim position

  We've reworked the pitch feel to replicate the variable-rate pitch feel
  of the real aircraft. Unlike other aircraft where the pitch feel is
  based on airspeed, the Challenger uses the stabilizer trim position as
  a stand-in for airspeed. The pitch response near the center gets more
  desensitized the more nose-down elevator trim is applied (implying
  flight at a higher speed). There is also a fixed "curve" that gets
  applied near the neutral point. This comes from a mechanical part of
  the elevator mechanization called the gain-change mechanism. This is
  more-or-less fixed and is always applied on top of the variable pitch
  feel from the stabilizer trim. We recommend removing any kind of curves
  you have applied to your joystick or yoke and try to get used to the
  new out-of-the-box feel.

  If you have a force-feedback yoke with controllable force intensity
  (such as a Brunner FFB yoke), you can disable the trim-dependent pitch
  feel in the User Settings under the User Interface tab. You can then
  replicate it in a proper FFB way by gradually increasing the force
  needed to move the elevator as elevator trim goes from 5.0 to 1.25
  (5=lighest, 1.25=heaviest). Outside of this range, the force should be
  constant, as the real pitch feel mechanism doesn't change force
  intensity outside of these ranges either.


2866: Implement dynamic GPS jamming simulation

  The CL650 now simulates dynamic, unannounced GPS jamming that happens
  in certain regions in the world, especially near disputed areas and
  active conflict zones. The locations of these areas are usually not
  NOTAM'ed, so you are encouraged to be on the lookout for potential
  issues with GPS reception in areas such as:

   - the Middle East
   - Eastern Europe
   - South China Sea
   - parts of Mexico

  Please note that these locations aren't hard-coded into the simulation.
  They dynamically change over time and needn't be active at all times.
  We can also add new areas post-release, and already have plans to add
  NOTAM'ed (scheduled and published) GPS outages.

  The simulation works by performing radio signal propagation modeling
  (including terrain masking) between the aircraft and every jamming
  station. If the signal levels of the jammer overpower the GPS satellite
  signals at the aircraft's position, the GPS position integrity will
  gradually degrade, until it is completely lost. You will then need to
  revert to inertial navigation and utilize radio or manual position
  updating. For now, we have chosen to avoid simulating GPS position
  spoofing, however.

  Please note that not all approach procedures can be flown without GPS
  available. Consult the approach procedure charts for required
  navigational sensors, as well as required navigational performance
  (RNP). This can then be cross-checked against the EPU value (Estimated
  Position Uncertainty) on the PFD as well as on the FMS PROG 2/2 page.
  Without GPS available, the FMC will attempt to use any enabled radio
  sensors (VOR/DME or DME/DME) as a source of position updates. Thus,
  flying an RNP 1.0 or sometimes even an RNP 0.3 approach might still be
  possible, provided that the approaches do not hard-require a GPS or
  GNSS sensor be available, and that a suitable position-updating navaid
  is available within range.

  For study purposes, the status of the jammer stations can be seen in
  the Study > GPS > GPS Jamming Stations window.

2927: Implement manual FMC position updating

  Dovetailing with the above GPS jamming functionality, the FMC now fully
  implements manual position updating. It is, admittedly, a very rarely
  used feature with GPS available, however, it does manifest in one
  useful way when in a GPS-denied environment. On departure, you will now
  have a "RWY UPDATE" prompt available on the ACT LEGS page on LSK 6L
  while the aircraft is on the ground. This can be used to manually
  update the FMC position to the runway threshold prior to takeoff, thus
  nulling out any positional drift due to purely inertial operation.

2963: Add ADG and nose gear door pins

  The aircraft now contains a beautiful 3D model of the air-driven
  generator (ADG, aka RAT on other aircraft), and together with that it
  brings an additional set of ground pins in the nose gear bay that must
  be manipulated by the pilot prior to and after a flight. The ADG pin is
  located on the right-hand wall of the nose gear bay, in the forward
  section. This pin locks the ADG in the stowed position, to prevent
  inadvertent ADG deployment while on the ground (restowing the ADG
  requires qualified maintenance personnel be called in). The second new
  ground pin is for the nose door and is located on the same right-hand
  wall of the nose gear bay, but more towards the aft section. For
  personal safety of ground crew while in the nose gear bay, the nose
  door is pinned, thus preventing any chance of the door closing and
  injuring personnel working there. This pin is typically installed after
  a flight and removed before a flight.

  These two additions complete the full set of 5 ground pins that are
  used in day-to-day operations.

2910: Refactor NAV-to-NAV transfer to avoid LNAV capture when APPR LOC is armed

  The NAV-to-NAV transfer system behavior was changed to behave more like
  the real airplane. When the aircraft is being vectored and utilizing
  HDG lateral mode, pushing APPR with a NAV-to-NAV approach loaded (e.g.
  an ILS) will no longer capture the LNAV path if the airplane happens to
  come close to the FMS path. Instead, *only* the armed APPR LOC mode
  will capture when the localizer begins to center. This helps prevent an
  inadvertent capture of the FMS path that might no longer be applicable.
  On the flip side, this means you will not be able to perform high-angle
  LOC captures (>45 degrees) by first capturing the FMS path in APPR LNV
  and then transitioning to APPR LOC. To perform a high-angle intercept
  with an intermediate step through the LNV mode, first push "NAV" on the
  FCP to arm the regular LNV mode for capture. Wait until the mode
  captures the FMS path and only then push the APPR FCP button to arm
  NAV-to-NAV transfer onto the localizer.

3036: Remove landing data that doesn’t exist in real box and add supplemental data message

  We've made fixes to the APPROACH REF computer to bring it in line with
  the quirks that the real avionics has. One of those particular gotchas
  is that you will no longer be able to compute an Actual Landing
  Distance (ALD) value when the runway condition is set to WET on page
  1/4. Instead, the box will simply post an amber '?' for the ALD value
  and you will get an amber PERF OUT OF RANGE message. For regulatory
  reasons, when the runway is wet, the only value to be used is the
  factored Landing Field Length (LFL). You can switch the ALD display to
  LFL by typing 'L' on the scratchpad and pushing LSK 4L on APPROACH REF
  page 2/4. This will remove the caution message and the FMS will show
  the factored (1.15x) landing field length instead. However, on the flip
  side, when the runway condition is set to any of the other contaminated
  settings (i.e. SLUSH-WATER, LSNOW, CSNOW or ICE), LFL becomes
  unavailable (and will post a PERF OUT OF RANGE message), and you will
  need to use ALD instead (place an 'A' on LSK 4L to switch to ALD
  display). The reason here is that there is no landing distance
  correction factor published for these contaminated runway conditions,
  so you will want to enter your own into LAND FACT on LSK 2L.

  An additional gotcha is that when the runway condition is set to
  anything other than DRY, the FMS will post a white SUPPLEMENTAL DATA
  message. This message cannot be avoided, and is intended to emphasize
  that the FMS isn't using data from AFM Section 6 (Performance), but
  instead from AFM Supplement 2 (Operation on Wet and Contaminated
  Runways).

2848: Implement route names and loading of routes by name

  You can now save and load pilot routes by name. This is done either by
  entering the name on LSK 2L of page 1 of the FPLN page, or by entering
  a custom name in PILOT ROUTE LIST on LSK 6L or LSK 6R.

  When a name is entered on FPLN page 1 LSK 2L, if the route doesn't
  already exist in the PILOT ROUTE LIST, the name is simply assigned to
  the current flight plan. This name can then be used as the route name
  in PILOT ROUTE LIST by pushing LSK 6L or LSK 6R. If a route with the
  same name already exists in PILOT ROUTE LIST, the user is prompted if
  they would like to load that route instead. Loading a pilot route into
  the active flight plan is not permitted while the aircraft is in the
  air.

2849: Support new VATSIM departure/arrival ATISes

  Some VATSIM regions have started publishing separate departure and
  arrival ATISes, just like some real airports do. Thus, the ATIS type
  selection on DATALINK > AOC CORP > ATIS now correctly attempts to pick
  the type-specific ATIS first, before reverting to the generalized one.

2860: Add volume control for FO audio

  You can now control the automatic first officer's audio volume when
  reading checklists. The setting is located in User Settings under F/O
  Assists.

New Features:

2823: Add IVAO Altitude client detection
2824: Add IVAO SELCAL integration
2825: Add support for showing COM TX flag on IVAO
2848: Implement route names and loading of routes by name
2849: Support new VATSIM departure/arrival ATISes
2860: Add volume control for FO audio
2866: Implement dynamic GPS jamming simulation
2869: Implement TOC and TOD display on MFD data window
2927: Implement manual FMC position updating
2953: Add search function to failure manager
2954: Add tooltips with descriptions to the Bleed study screen
2955: Add ASU engine parameters to the Bleed study screen
2963: Add ADG and nose gear door pins
2988: Elevator control system is missing gain change mechanism from control column, causing over-controlling at higher speeds
3121: Implement variable pitch feel based on stabilizer trim position
2995: Need to implement ADG ADCU failures in the failure manager
2996: Implement missing stall protection system failures
3002: Add datarefs to expose the internal CL650 atmospheric model
3006: Implement a dataref interface to wire and ARINC-429 abus data
3116: Need a ground service menu option to fix a rotor lock


Improvements:

2816: MFD radio controls should have a test function on the NAV radio
2847: PROG page should show MANUAL or MEASURED in title when using the respective FUEL MGMT mode
2858: Update windshield heating auto-checklist to select either LOW or HI before takeoff
2778: Selecting SID/STAR does not narrow down runways
2435: Rudder needs more effectiveness to cope with V1 cut
2872: Make circuit breakers require a long click to pull to help avoid accidentally pulling breakers by randomly misclicking
2885: Show airframe manager when aircraft is repositioned using X-Plane flight setup screen
2898: Refine VOR/DME and DME/DME tuning when in the approach phase
2707: Need to show a magenta "FROM" flag next to the PFD horizontal deviation bar when flying from an FMS waypoint
2902: Refactor RNP APPR and RNP AR APPR determination to follow proper ICAO PBN rules
2908: Adjust electrical loads of components to be slightly more realistic
2910: Refactor NAV-to-NAV transfer to avoid LNAV capture when APPR LOC is armed
2912: Refactor autopilot and IRS code for more stable operation in ATT mode
2914: 10th stage bleed study screen needs to color in the vacuum ejector line using the temperature of the vacuum line
2915: Refactor tooltip system to use cairo rendering and XP11 modern windows for proper scaling
2918: Readjust tire drag down a bit to roll more easily on idle thrust
2944: Hoppie ACARS DEPART CLX system needs to handle clearance confirmation and error messages
2966: Add documentation link to the Study menu
2983: Allow user to specify a custom OCEANIC CLX facility in user settings
2985: Implement engine fuel feed lines as having a volume of fuel for delayed fire shutoff valve reaction
2991: Default the nose door to open on new persistent airframes
2696: During SPS test needle should go past red zone due to rate-advance mechanism
3036: Remove landing data that doesn’t exist in real box and add supplemental data message
3061: Redesign TUNE page parsing to be much more strict
3063: Selecting TO or GA should always activate the TO thrust limit
3117: When an in-flight state is repositioned back to the ground, reset core temps to allow immediate shutdown without core lock


Bugfixes:

861: TUNE page should not allow entry of 4 letter LOC idents
2808: Leftover experimental GS steering code is causing pitch oscillations
2807: Squawk code transmission is broken in ARINC622 format
2806: UM74 and UM75 direct-to interoperability with Hoppie CPDLC broke prior to 1.5 release
2809: Maximum distance for DIS CROSS on FIX INFO should be 500 miles, not 200
2810: Galley normal map has excessive gloss
2811: Crash when airplane is dragged up into the air in turn estimation code
2813: Crash when selecting direct-to the last waypoint on an airway if followed by a discontinuity
2815: NAV radio test wasn't generating the correct test data out of the NAV-4000 and DME-4000 radios
2817: When an intercept leg his an IF-TF target, it incorrectly marks the intercept leg as virtual, instead of the IF leg
2821: PAX hurry up call option is broken
2802: APU GEN off caused CTD, broke airframe file
2768: Changing NAV SRC while OEI causes CTD
2803: Crash due to dangling airway-to-waypoint mapping table left over after a navigational database swap
2822: MFD Nav Radio Missing Auto Label
2828: Closing a disco in front of a VECTORS transition isn't generating a TF leg segment properly
2440: When a NAV radio is set to auto tuning, manual tuning via MFD doesn't work
2801: CTD when using DTO history
2829: ETA column on FPLN PROG MFD DATA page is computed incorrectly on TOD when TOD is on current leg
2830: DIR-TO page isn't showing required path angle and VS on page 1
2832: Alternate cruise altitude isn't being used in alternate fuel use calculation
2833: ROSE mode TO-FROM flag should be drawn with a black outline, not black-filled
2834: FPLN sequences prematurely when crossing 180 degrees of longitude
2835: IRS hybrid position solution needs to handle GPS position wrapping
2837: Add Altitude and POSCON to list of supported networks/clients in user settings
2819: CTD crossing 54N040W
2838: Mandatory turn direction can be mishandled by LNAV in certain corner cases
2839: Pilot oxygen mask blockage failure condition inverted, resulting in zero oxygen consumption
2841: Limit CPC auto valve rate to prevent oscillations when high cabin altitude condition is encountered
2840: Implement explicit versioning of serialized data sets to avoid persistent breakage of state files
2842: Entering a single-digit or two-digit radio frequency should tune the matching frequency preset slot
2843: Entering more than an 8-character frequency slot name in TUNE page crashes
2844: Moving VS/Pitch wheel should revert to Pitch mode unless the active vertical mode is VS or GS capture
2846: TO and GA vertical modes should be cleared by AP engagement or pushing the FD SYNC button
2850: Rounding of coordinates can cause a copy-back of 60 minutes out of a fix definition
2851: Geographic coordinate entry must allow entering 180 degrees of longitude
2852: When going direct-to the first waypoint on an airway, the direct-to path construction goes haywire
2854: Don't allow editing VNAV data on FA legs
2855: Inserting PDW at end of FPLN while in the air causes the FPLN to go direct-to the PDW instead
2857: Using FLEX takeoff results in spurious VSPEEDS DESELECTED when changing altitude in flight
2859: Update 3rd party docs to latest state
2861: Always clamp FD pitch command to allowable range
2862: Don't do terrain auto-popup on the PFD during a TAWS test, only during a genuine TAWS caution or warning
2863: When a CPDLC direct-to targets a navaid or airport as a FIXNAME, INSERT MOD into the FPLN fails
2864: When an FC leg occurs on a 5-character waypoint, the length field gets truncated to show only the leading zero
2556: Clock Local time is non-functional
2875: Pitch servo mistuning during G/S approaches was causing divergent oscillation at lower framerate
2876: Missing altitude in POSITION REPORT message human-readable format just before the "NEXT" word
2878: RNP approach handling without GNSS is producing spurious FMS messages
2879: Hoppie CPDLC interface needs to support climb and descent rate messages
2882: Boost pump INOP light and CAS messages should come on when on ground and the pump switch deselected
2883: Don't post ATS FAIL when no ATS mode is active and T/Rs are selected
2877: Secondary motive flow supply line occurs after the main ejector check valve, not before it
2884: Don't compute CLB, CRZ and MCT N1 targets when engine bleeds are off
2881: BACK ON ROUTE triggering too early, while still very far cross-track
2880: Waypoint ETA time computation unstable due to floating point rounding
2886: libcpdlc - deleted some dead code from ARINC 622 refactor
2887: libcpdlc - POS REPORT FANS page isn't automatically picking up FMS-supplied waypoint name data
2888: libcpdlc - altitude and speed display is doing incorrect rounding
2889: IRS study window wind component needs to be reversed and have proper alignment and units displayed
2890: TOC data shouldn't show on VNAV window
2891: TOD shouldn't show on VNAV window unless we're close to it
2893: Don't show TOC and TOD lines on FPLN PROG MFD DATA page when they're no longer relevant vertically
2894: Don't produce a vertical track alert when we're already below the TOD
2897: NRST APTS map symbols on AFDs need to respect the minimum runway length limit set in DEFAULTS
2900: Spurious APPR NOT AVAILABLE when an approach is marked for RNAV-any-sensor even though IRS is available
2901: Don't flash waypoint name on PFD when approaching it if FPLN sequencing is inhibited
2904: THRUST LIMIT page should show VERC label, not VFTO, during single-engine enroute climb or driftdown
2907: LPV approaches flown as RNP aren't bringing up the RNP ARM and RNP APPR messages
2913: Procedures with legs whose course is referenced to a LOC or ILS emitter's magvar are having the airport's magvar applied instead
2903: Non-applicable "Sit in Seat" menu items will now be disabled based on user location
2916: Add animation datarefs for ADG
2917: ADG drop at high speed stalls the turbine blades and doesn't come up to full speed
2920: Rename CL650/adg/phi dataref to CL650/adg/pitch
2922: Reacquisition of nav radio corrections after long period of no corrections doesn't wash out accumulated variance quickly enough
2923: FMS-FMS DISAGREE message mustn't compare the position of the non-active FMS
2921: FPLN with DEST only crashes when a departure runway is selected from arrival airport while on the ground
2924: LOC and VOR steering is too lethargic at larger distances
2925: Don't drop EPU when doing navaid retuning
2926: New tooltip system needs support for custom fonts with unicode characters
2928: Don't dump TACAN-colocated DMEs from the radio simulation
2929: Entering PAX/WT in one go doesn't correct convert LBS passenger weights, resulting in spurious INVALID ENTRY
2932: TERM WX VIEW page has carets on the wrong side when available airports overflow to the right-hand side
2933: Vertical prediction gives incorrect climb path for simple flight plan
2936: PL21 FMS FPL test program doesn't resolve airport and runway arguments to the "pos" command correctly
2937: Move climb mode variable into tighter scope in solve_vnav_clb_misap
2938: Don't hard-assert that we need elevation in FPL path solver
2939: Automatic VOR/DME updating facility shouldn't try to tune in TACANs
2941: Don't attempt radio corrections if the station is more than 45 degrees slant angle
2942: Don't post FMS DR and LOW POSITION ACCURACY messages when on the ground
2943: Radio correction distance misestimation due to altimetry errors and slant angle needs to be taken into account
2945: Manually setting position on the ground should set all FMCs at the same time
2946: In certain cases, going direct-to can cause the VNAV to enter descent mode prematurely
2947: When shortening procedures, update the TO side of the procedure line to reflect the new termination waypoint
2948: Doing a vertical direct-to to a CF leg that is also a lateral direct-to results in incorrect VDEV computation
2949: Disable IRS soft realign in preflight phase to avoid generating bogus alignments if the airplane starts moving
2950: Add extra FSCU table data for estimating very low AUX tank levels and aircraft is in an on-ground attitude
2951: Desensitize amber GNSS NOT AVAILABLE message so it doesn't always come up on the ground when powering up
2957: Creating or deleting custom states doesn't immediately sync the airframe database to persistent storage
2958: HUD rendering isn't stopping when the HUD combiner is stowed
2960: Refueling on uneven terrain can fail to hit the HL switch on the higher wing
2962: Add special case for abbreviated 833 frequency entry for 16xxx to 19xxx
2964: Reduced half bank isn't being used when it should
2961: Restore XP squawk code datarefs explicitly during a state restore
2968: ATS PIDs need to be reloaded from master config even on a state reload so we don't keep reusing old PID params
2970: Relax FPL deserialization when loading persistent disk FPLs in case the NAV DB has been changed or corrupted
2972: Optimize ARINC 429 code to avoid using avl_walk wherever possible
2973: Expose runpool profiling datarefs in non-debug builds
2974: Don't redraw cabin info screen when camera is far away from the airplane
2845: Chart zoom commands’ description is backwards
2980: Optimize PFD ADI drawing by removing explicit black outlining of certain text elements that aren't outlined on the real avionics
2979: EPU shouldn't be being drawn on compressed PFD
2978: Bearing display on compressed PFD doesn't fit vertically into the PFD
2981: Reduce Hoppie polling interval to 1 minute
2982: When DTG is unavailable on PFD, show it as 4 dashes, not dash-period-dash
2986: Show white NO APPR if a loc-check occurs during NAV-to-NAV setup
2997: Backup low speed cue in absence of Aux AOA signal should show enhanced red band instead of plain solid
3001: Refine autopilot pitch steering to get rid of "shaking" of yoke when AP is making large inputs
3005: LNV steering mode is prone to some oscillation at higher speed
3007: Bleed flow system mis-accounts bleed mass-flow demands, resulting in too high running ITTs
3011: Don't compute a TO N1 limit with 10th stage bleeds and anti-ice selected on
3008: Automatically check the respective minimums box when the DCP DATA knob is spun while setting REFS
3012: When baro minimums are selected, ALT SEL should snap to the baro mins value when rolled through it
3018: Update GPS Almanac URLs to new ones
3025: Implement variable rate trim commands from FCC as they should be PWM, not constant
3033: Extended no-manip section of cabin and fuselage to avoid clicking through to outside manipulators
3027: Pin missing on Nose Gear torque links (scissor links)
3030: Autopilot should be available when on EMER POWER ONLY
3021: Flying the KLEW ILS 04 from ENE w/HILPT causes a CTD when turning inbound
3029: At airport 3J7, the fueler is asking for liters when it should be asking for gallons
3037: Reduce min volts for most avionics modules to avoid a reset during a hard generator under-power trip
3042: VNAV direct-to shouldn't clear constraint class on intermediate legs if there is still a speed constraint on the leg
3043: VNAV phase can revert to CLB if TOD is constructed based off a descent constraint on an enroute leg
3045: "Requires Better Pushback" note on handling request form is misplaced vertically
3047: Hoppie """CPDLC""" likes to send lowercase in messages, so auto-uppercase everything
3048: Don't round BOW and AVG PASS WT values in defaults
3050: When left collector is nearly empty, ejector pump incorrectly over-calculates delivery pressure, causing APU cutout
3051: Arc legs can turn the wrong way if the aircraft intercepts at a steep angle and is outside of the arc start/end radial
3055: Entering wind component on TAKEOFF REF or APPROACH REF shouldn't zero the value if no H/T/P/M is given
3056: Permit fly-by of fix terminations if followed by intercept legs which would trigger before the fix termination
3057: Distance and radial terminated legs need to allow for fly-by unless explicitly tagged as overfly
3062: Don't allow fuel truck hookup with beacon light on
3064: Refine steering around tight arcs for RNP-AR approaches
3039: GPS doesn't correctly compensate for time-acceleration on velocity trends
3066: When an intercept leg overshoots an arc due to turn radii, prevent an intercept from happening on the far side of the arc
3067: Don't do direct-to joins on the next leg when a DF is followed by a TF
3072: Need support for RF legs with more than 270 degrees of arc
3071: LNAV should use rough altitude estimation to correct groundspeed and do turn prediction further down the FPL
3070: V-MDA PATH guidance isn't aiming at the runway or airport, but instead at the MAP
3073: AC ELEC page line from APU gen to APU data box should be filled green when APU gen is available and selected on
3074: Use previous pass VNAV altitudes for turn estimation during the LNAV construction pass
2190: Don't allow entering 3-digit abbreviated frequencies into COM tuning field
3076: Show INVALID CHANNEL instead of INVALID FREQUENCY on incorrect channel entry into COM tuning fields
3079: Vatsim """CPDLC""" sometimes uses CONTACT messages with reversed arguments
3078: SBAS integrity check should only be performed in LPV approach mode or on approaches where SBAS is mandatory
3082: Redesign VNAV phase determination to be much simpler and more reliable
3083: FMC2 checks the wrong GNSS side for disable status before using it
3085: VNAV SETUP transition alt/level entries should reflect the same value as used for the FL ALERT
3087: Hoppie """CPDLC""" messages can sometimes include a trailing " FT" part in altitude arguments
3089: Add additional detection of Hoppie logon rejections
3090: Reduce the engine vertical cant slightly to line up closer to technical docs
3093: AFD heading and engine data isn't being properly cleared out when the system is powered off
3094: Disabling FD should disable VNAV mode
3096: Need to handle Hoppie "MESSAGE NOT SUPPORTED BY THIS ATS UNIT" message
3099: Performing T/R check on the ground shouldn't cause the ATS to go FAIL, and only DISENG'D if active
3098: Deselecting TO mode on the ground should kill N1 TO ATS arming
3101: When ATS disengages automatically in landing mode, don't flash amber DISENG'D on the MSD
3104: Reduced bank angle heading control is unstable
3108: Refine GP mode steering when large trim changes are required due to flaps deployment and speed changes
3109: Don't attempt to process gear-related CAS messages from bad data when both PSEUs fail
3110: Parking brake config warning must come on when in the air or PSEU is failed
3106: ATS MSD should go blank after 7 seconds of SERVOTST
3112: Prevent removing a ground pin when the PSEU is attempting to move the corresponding actuator
3115: Refactor final VNAV path construction to start at the runway, not the FAF, except in case of V-MDA approaches
3122: Fix gap between top edge of overhead base and ceiling
3123: Arrivals with STAR terminating in vectors without a bottom altitude will fail to capture PATH mode
3124: VNAV doesn't stop on a level segment if the subsequent leg's altitude constraint is lower
3125: Entering a nonexistent airport into ORIGIN with no flight plan will crash
3126: Implement more route name entry validation
3127: Cruise speed determination is incorrectly converting m/s to knots and resulting in bad estimation when cruising below Mach
3128: Fixed gap between meshes in vertical stabilizer
3032: Fuel cap and forward equipment bay doors are missing lock/unlock decals
3015: 3 screws on radalt antenna on tail of aircraft are doubled-up and z-fighting
3133: Fixed gaps on rough section of power lever handles Normal Map.
3132: Don't allow loading pilot route directly into ACT FPLN while in the air
3134: If FMC groundspeed is momentarily invalid, it can cause FMC3 to crash

Dernière modification par Epikk (25-06-2022 09:01:20)


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#152 [↑][↓]  26-07-2022 12:29:29

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

En cours de Beta 1.7, leur vision du cockpit partagé est juste énorme et terriblement stable

Dernière modification par Fuchs (27-07-2022 10:34:30)


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#153 [↑][↓]  26-07-2022 20:34:24

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Whoop whoop !!! eusa_clapw00t


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#154 [↑][↓]  30-08-2022 09:56:17

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Beast

https://youtu.be/cHG-U2KslxA

Dernière modification par Epikk (30-08-2022 09:56:58)


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#155 [↑][↓]  30-08-2022 09:57:43

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Souci avec ton intégration mon copain!

Dernière modification par Fuchs (30-08-2022 09:58:12)


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#156 [↑][↓]  30-08-2022 12:36:20

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Merci Fab.


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#157 [↑][↓]  21-12-2022 18:54:43

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

v1.7 disponible... Masterpiece...

Je pose ça là...
https://forums.x-pilot.com/forums/topic … -released/


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#158 [↑][↓]  21-12-2022 19:07:39

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

cet addon est juste insolent...


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#159 [↑][↓]  21-12-2022 20:26:57

flomartin
Copilote
Date d'inscription: 25-12-2013
Renommée :   

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

C'est super impressionnant...

J'aimerais avoir le temps d'apprendre à utiliser ce bel avion !


Intel i7 9700KF, nVidia 3090, 64 Go de RAM.

Hors ligne

 

#160 [↑][↓]  03-01-2023 16:55:49

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

w00t

Des grands malades, une joie cet addon!!

https://forums.x-pilot.com/forums/topic … start-apu/


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#161 [↑][↓]  03-01-2023 17:29:07

ydelta
Pilote Virtuel
Membre donateur
Lieu: FL 390
Date d'inscription: 26-07-2015
Renommée :   128 
Site web

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Ca a pas l'air hyper pratique pour faire un reset de l'APU sur cet avion si une faute survient en plein vol laugh


PC1: i9 9900K @5.2 Ghz - Gigabyte GEForce RTX 4080 OC 16 Go - Asus Z390 Pro Gaming - 32Go de RAM DDR4 3200Mhz / PC2: i7 8700K OC 5.1Ghz - Geforce GTX 1070 OC 8Go - Asus ROG Maximus X Hero - 32Go  DDR4 @ 3200 - SSD 5.5To
Portable: Asus ROG 703GL - i7 8750H- GTX1070 8Go - 32Go DDR4@2666 - 2To HD + SSD

Hors ligne

 

#162 [↑][↓]  03-01-2023 18:17:46

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

L'addon a un an aujourd'hui... ils fêtent avec un petit Group Flight


Dernière modification par Epikk (04-01-2023 23:23:53)


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#163 [↑][↓]  03-01-2023 21:30:43

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Oui, helas, j'ai pas eu l'occasion de me libérer à temps pour participer...


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#164 [↑][↓]  04-01-2023 11:13:15

FreeB!rd
Commandant de bord
Lieu: Par-ci, par-là
Date d'inscription: 27-12-2011
Renommée :   56 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

ydelta a écrit:

Ca a pas l'air hyper pratique pour faire un reset de l'APU sur cet avion si une faute survient en plein vol laugh

Y'a pas b'soin de l'APU en plein vol wink

A savoir que pendant le live, Toto aurait laissé quelques indices sur le prochain avion sur lequel ils vont travailler.

Lu sur le Discord : "News spreads fast, I guess. Well, after some trial & error, folks guessed our hint in the stream. We're doing an A220 / C-Series. Not sure yet if the -100 or -300 is gonna be first, but we'll do them both."

Hors ligne

 

#165 [↑][↓]  04-01-2023 12:22:25

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

FreeB!rd a écrit:

ydelta a écrit:

Ca a pas l'air hyper pratique pour faire un reset de l'APU sur cet avion si une faute survient en plein vol laugh

Y'a pas b'soin de l'APU en plein vol wink

A savoir que pendant le live, Toto aurait laissé quelques indices sur le prochain avion sur lequel ils vont travailler.

Lu sur le Discord : "News spreads fast, I guess. Well, after some trial & error, folks guessed our hint in the stream. We're doing an A220 / C-Series. Not sure yet if the -100 or -300 is gonna be first, but we'll do them both."

Super nouvelle qu’il ait déjà choisi son prochain projet.
Le temps qu’il finisse le CL650 et commence l’A220 on a le temps de voir venir je pense…


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#166 [↑][↓]  04-01-2023 12:36:26

FreeB!rd
Commandant de bord
Lieu: Par-ci, par-là
Date d'inscription: 27-12-2011
Renommée :   56 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Epikk a écrit:

FreeB!rd a écrit:

ydelta a écrit:

Ca a pas l'air hyper pratique pour faire un reset de l'APU sur cet avion si une faute survient en plein vol laugh

Y'a pas b'soin de l'APU en plein vol wink

A savoir que pendant le live, Toto aurait laissé quelques indices sur le prochain avion sur lequel ils vont travailler.

Lu sur le Discord : "News spreads fast, I guess. Well, after some trial & error, folks guessed our hint in the stream. We're doing an A220 / C-Series. Not sure yet if the -100 or -300 is gonna be first, but we'll do them both."

Super nouvelle qu’il ait déjà choisi son prochain projet.
Le temps qu’il finisse le CL650 et commence l’A220 on a le temps de voir venir je pense…

Complètement ! Ajoute à ça qu'il bosse aussi sur la maj du TBM900 pour XP12.
Encore quelques années devant nous, et ça tombe bien, j'ai pas envie de passer à autre chose que le Chally !laugh

Hors ligne

 

#167 [↑][↓]  04-01-2023 12:52:21

flomartin
Copilote
Date d'inscription: 25-12-2013
Renommée :   

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Un A220 !!!!!


Super bonne nouvelle !!! Comme ça risque d'être mon prochain avion, j'achète direct à la sortie :)


Intel i7 9700KF, nVidia 3090, 64 Go de RAM.

Hors ligne

 

#168 [↑][↓]  04-01-2023 15:46:47

ydelta
Pilote Virtuel
Membre donateur
Lieu: FL 390
Date d'inscription: 26-07-2015
Renommée :   128 
Site web

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

FreeB!rd a écrit:

Y'a pas b'soin de l'APU en plein vol wink

Evidemment pas en conditions normales mais sans connaître le détail des procédures pour le Challenger 650, il doit bien y avoir un cas de DUAL ENGINE OUT qui requiert un redémarrage de l'APU pour fournir du BLEED air pour l'engine relight procedure si pas de windmilling possible.


PC1: i9 9900K @5.2 Ghz - Gigabyte GEForce RTX 4080 OC 16 Go - Asus Z390 Pro Gaming - 32Go de RAM DDR4 3200Mhz / PC2: i7 8700K OC 5.1Ghz - Geforce GTX 1070 OC 8Go - Asus ROG Maximus X Hero - 32Go  DDR4 @ 3200 - SSD 5.5To
Portable: Asus ROG 703GL - i7 8750H- GTX1070 8Go - 32Go DDR4@2666 - 2To HD + SSD

Hors ligne

 

#169 [↑][↓]  04-01-2023 23:26:57

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

FreeB!rd a écrit:

Encore quelques années devant nous, et ça tombe bien, j'ai pas envie de passer à autre chose que le Chally !laugh

On est d'accord... trop de la balle. C'est un autre level...

Dernière modification par Epikk (04-01-2023 23:34:55)


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#170 [↑][↓]  05-01-2023 00:32:40

ydelta
Pilote Virtuel
Membre donateur
Lieu: FL 390
Date d'inscription: 26-07-2015
Renommée :   128 
Site web

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Epikk a écrit:

On est d'accord... trop de la balle. C'est un autre level...

Après Level D c'est Level E alors  laugh

--> je sors


PC1: i9 9900K @5.2 Ghz - Gigabyte GEForce RTX 4080 OC 16 Go - Asus Z390 Pro Gaming - 32Go de RAM DDR4 3200Mhz / PC2: i7 8700K OC 5.1Ghz - Geforce GTX 1070 OC 8Go - Asus ROG Maximus X Hero - 32Go  DDR4 @ 3200 - SSD 5.5To
Portable: Asus ROG 703GL - i7 8750H- GTX1070 8Go - 32Go DDR4@2666 - 2To HD + SSD

Hors ligne

 

#171 [↑][↓]  14-01-2023 11:12:56

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

https://i.ibb.co/L9LLB8g/CL650-2023-01-14-03-42-56.png

Don't do it Toto !

Dernière modification par Epikk (14-01-2023 11:14:11)


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#172 [↑][↓]  14-01-2023 12:18:51

Fuchs
Pilote Virtuel
Membre donateur
Lieu: EBLG - EBTX
Date d'inscription: 25-10-2009
Renommée :   97 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

=w


Amat Victoria Curam
I7 9700k @5.0Ghz / Asus Z390 / MSI 1080ti GamingX / 32Go RAM /Samsung 4K 49" / Rift S / etc, etc, etc...

Hors ligne

 

#173 [↑][↓]  17-01-2023 06:45:07

Epikk
Commandant de bord
Lieu: LFBD
Date d'inscription: 18-08-2008
Renommée :   42 

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

https://i.ibb.co/bgC5rgc/CL650-2023-01-17-06-22-35.png
Please don't heart them Toto !


Cheers, Fritz ESSONO
"You know nothing Jon Snow..."
A2A :: FSLabs :: HotStart :: Leonardo SH :: Level-D :: Majestic :: RealAir :: VRS :: NO "BALTRINGUEWARE" ALLOWED

Hors ligne

 

#174 [↑][↓]  17-01-2023 12:46:53

Branech
Copilote
Date d'inscription: 18-02-2011
Renommée :   

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Dommage que le Hot Start Challenger 650 ne soit pas finalisé pour la VR.

Pour le prix très élevé de cet avion, cela n'est pas normal.

Je ne l'achèterai donc pas tant qu'une mise à jour VR ne sera pas proposée.

Hors ligne

 

#175 [↑][↓]  17-01-2023 15:34:37

flomartin
Copilote
Date d'inscription: 25-12-2013
Renommée :   

Re: [X-Plane]Hot Start Challenger 650 [DISPO]

Je trouve la modélisation juste sublime...Comme le reste d'ailleurs.

Vraiment un des meilleurs add-ons du moment.


Intel i7 9700KF, nVidia 3090, 64 Go de RAM.

Hors ligne

 

Pied de page des forums

Maintenance informatique Lausanne